Important Plumber Tips for Bathtub Installation
Important Plumber Tips for Bathtub Installation
Blog Article
Just how do you really feel with regards to A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't exactly brain surgery, yet it does require solid plumbing, carpentry, and in some cases, tiling skills. Changing an old tub with a new one is additionally a reasonably challenging project. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open up a wall surface to remove the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old bathtub and set in the new one. Make sure you have actually qualified yourself for the work as well as fit attempting it. Instead of working with a professional to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This article will help you install a new bath tub in your restroom if you have actually currently bought a new bathtub and also do not need to change the setup of your previous supply of water pipes.
Your devices as well as product checklist should consist of the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of eliminating the existing taps can be fairly problematic due to the limited access that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the maker offered backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Using the two wood boards under its feet, position the bath tub in the called for position. The wooden boards are valuable in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub till the level checks out degree.
To set up taps, fit the bottom of the furthest flexible faucet adapter to the appropriate supply pipeline by making a compression join; then do the same for the various other tap.
Switch on the water as well as check all joints and also new pipework for leakages as well as tighten them if required. Load the bathtub as well as likewise examine the overflow electrical outlet as well as the regular electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling and securing around the tub needs to wait until the bath tub has been made use of at the very least once as this will resolve it into its final position.
Getting ready for the Installation
Firstly, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to crack an inflexible seal, causing the water to pass through the wall surface between the bathroom and the tiling, bring about problems with wetness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can crack fairly early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our part about A Step-by-Step Guide to Installing a Bathtub. Thanks for taking a few minutes to browse our blog post. Please set aside a second to share this article if you enjoyed reading it. We cherish reading our article about How to Install a Bathtub.
Drain woes? Connect. Report this page